GENERATOR W/ 10-STEP FREQUENCY MODULATION FOR PRECISION OUTPUT
Cold Corona Discharge
per Milleter ( mcg / ul )
PERFORMANCE OUTPUT SAMPLE
All outputs are approximate since ozone concentrations vary
with humidity and temperature and other environmental conditions
at the site in which the generator is being used at the time
it is being used. The output concentrations listed on this sample
are figured on 100% oxygen sourced (not
air), set on #10 on the 10-step frequency dial.
USES: Air, Water, Essential Oils, Rectal Insufflations,
Ear Insufflations, Vaginal Insufflations, Topical Bagging or
Cupping. Use only with tank oxygen or a quality oxygen concentrator
to ensure gas is dry. May be used with a "air dryer"
of using air sourced oxygen for air purification or bubbling
thorugh essential oils to make ozonides.
Topical Use : we suggest putting the dial on #7 or
8 and set the oxygen flow for 1/4 LPM and waiting approx. 2 min.
for the sauna to fill (or whatever you're using it for).
Water: Attach a bubbler (ceramic ones are available
through Aquarium Suppliers/Pet stores) and bubble into distilled
water. The rule of thumb is the colder the water, the longer
the 1/2 life of the ozone. Typically 40 min.-2 hrs. in refrigerated
distilled water (DO NOT OZONE WATER IN PLASTIC BUT GLASS ONLY
SINCE PLASTICS MAY LEECH BREAK DOWN PRODUCTS INTO THE WATER...A
GLASS PITCHER OR APPLE JUICE JUG WORK WELL...)
Far Infraared Sauna Users: Make sure there is a small
desktop fan blowing air towards the generator to reduce breathing
gas and place a wet wash cloth over nose and mouth to help ozone
turn back into 02 and water and not irritate eyes. If eyes get
irritated, put wet wash cloth over eyes also while using ozone
For each step on the 10-step frequency dial, figure on reducing
output 10% from the previous setting. In other words, if you
have your oxygen flow rate at 1/2 lpm and the dial set to #10,
the unit is putting out approx. 16 mcg/ml. (mcg.03 per ml. of
02). according to the chart above. If you turn the dial to #9,
while leaving the oxygen setting where it is at 1/2, you are
reducing the output by approx. 1.6 lpm (10%) so the output will
be around 14.4 mcg/ml. It is not an exact linear relationship
but it gives a ballpark which is what we're interested in.
Remember the rule of ozone generation: The longer
the oxygen is in contact with the dielectric, the stronger the
ozone will be (in other words, the slower the oxygen flow rate,
the stronger the ozone output). You combine slower flow rate
with more electronic frequency control and you have many more
Individual certification of the output of each flow rate and
each frequency is available from our supplier but is very expensive
since having that information is only important if you're using
it for medical applications and since these units are not certified
for medical but industrial use (eventhough the "guts"
are basically the same), the manufacturer won't give a certified
output chart with each unit but chooses rather to give a general
performance chart. We have modified their chart to reflect the
use of 100% oxygen gas rather than air.
NOTE: The frequency switch noise is intentional to
ensure the unit is not left running unattended and damaging the
components. Do NOT put a pillow or other obect over the generator
to quiet it since that will block the ventilation which is critical
For convenience sake, we recommend use with a power strip
with an off/on switch since the units don't come with one.
Ozone Generation Method: Silent pulse injection corona discharge
Gas Source: Dry air or oxygen, free of dust and oil. Max pressure
+/-0.36 bar (5psi)
Ozone Production: 500 mg/h from dry air at 3L/min. dry air flow;
1000 mg./hr. from 100% oxygen; 250 mg./h at 4 LPM ambient air
at 50% R.H. (1 L/min=2 SCFH)
Cooling: Self-cooled cabinet. Ambient Air. +/- 40°C. Max.
85% relative humidity. (May add an external fan in hot environments
to ensure extra cooling)
Power: 120v/60 hz/0.2A 25W standard or 0.4A 50W with optional
Options: Air pump / 10-position switch for ozone control from
10 to 100%
Dimensions: 14"L x7"W x 4"H Brushed Stainless
Steel w/protective coating which can be peeled away. Key holes
Certifications: Warnock 7 Hersey Certified. CSA file L18014-Canada
ETL file #98260-USA
Safety: A minimum air flow is not required. If using water, an
Azcozon balance barometer is required.
Warranty: Manufacturers. 3 years general. The rate of the air
drying desiccant depletion is subject to local air quality, and
it is expected to last 3 years in normal conditions. Premature
depletion of the desiccant is not covered under warranty.
Most repairs or service can be done by our supplier. Please allow
30 days since they need to be shipped and returned from Canada.
AHW100 OZONE GENERATOR
LOW FLOW 0-4 LPM OXYGEN REGULATOR
(increments of 1/8th)
AND OIL KIT
NASAL CANNULA FOR E.W.O.T.
14 Fr Catheter for rectal
& vaginal insufflations
Extra TEFLON Connectors (T,
Extra UV Cured Silicone Tubing
($2.50 per ft.)
NOT INCLUDED BUT REQUIRED
CGA 540 STYLE WELDING OXYGEN
TANK. CUSTOMER MUST PURCHASE THIS AT A WELDING SUPPLY THEMSELVES.
DO NOT TELL THEM IT IS FOR HEALTHCARE USE.
IMPORTANT NOTE: This unit
can be used with air or oxygen. Air fed generators MUST have
an air drier to absorb atmospheric moisture to prevent destruction
of the corona discharge unit inside which will rust out otherwise.
IF AN AIR DRIER IS REQUESTED, ADD $600.00. Some prefer to buy
an oxygen concentrator which contains an air drier.
$1650.00 USD + S & H
Mandatory FDA Disclaimer:
The statements & products shown on this website have not
been evaluated by the US Food and Drug Administration. Statements
are not intended to constitute professional advice for treatment
of any disease but are for educational purposes. These products
are not intended to diagnose, treat, cure or prevent any disease.